Mpio DMG Manuel de service Page 24
- Page / 64
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Table 5 describes NVRAM settings.
Table 5 NVRAM configuration
Default settingSettingsDescriptionField
Disabled
Enabled
Disabled
Enabled—Allows you to enter a value for the
FC-AL address.
Disabled—The device selects and configures
an available address when the FC loop is
initialized.
Hard Address En-
able
0
0–125
If hard addressing is enabled, allows you to
set the FC-AL hard address.
Hard Address
N/AN/ANot supported with Mac OS X.Loop Retry Count
2048
512
1024
2048
Determines the size of FC packets. Typically,
the initiator and target negotiate the frame
size, starting with the largest possible value.
For normal operation, set the frame size to the
largest value.
Frame Size
Port WWN
Node WWN
Port WWN
Specifies the type of device discovery the ad-
apter performs.
Note:
Device Discovery must be set to Port WWN
to enable multiple paths to the EVA controller.
Device Discovery
PTP Preferred
Arbitrated Loop (AL)
Point-to-Point (PTP)
AL Preferred
PTP Preferred
Determines the type of channel connection:
Arbitrated Loop (AL)—Connects to an
arbitrated loop or a fabric loop port (FL_Port)
on a switch.
Point-to-Point (PTP)—Connects to a direct
fabric connection, such as an F_port on a
switch.
AL Preferred—Allows the host adapter to select
the type of connection, but attempts to connect
in AL mode first.
PTP Preferred—Allows the host adapter to
select the type of connection, but attempts to
connect in point-to-point mode first.
Connection Mode
321–255
Specifies the maximum number of LUNs that
can be presented to the server from the EVA.
Important:
All channels must have the same setting to
ensure that LUNs use all available channels.
Max LUNs per Tar-
get
Auto
1 Gb/s
2 Gb/s
4 Gb/s
8 Gb/s
Auto
Determines the FC transmission rate.
When set to Auto, the adapter negotiates the
rate based on the connected device.
Data Rate
ATTO Configuration Tool24
- Part number: 5697-0025 1
- Third edition: July 2009 1
- Contents 3
- About this guide 7
- HP technical support 8
- Subscription service 8
- HP websites 9
- Documentation feedback 9
- Configuration guidelines 12
- Setting up the host system 13
- Single-path connectivity 14
- Multipath connectivity 14
- Verifying the configuration 17
- 3 ATTO Configuration Tool 19
- ATTO Configuration Tool20 20
- Localhost device 21
- Adapter device 22
- Channel device 23
- Table 5 NVRAM configuration 24
- NVRAM buttons 25
- EVA controller 26
- DescriptionInformation type 27
- ATTO Configuration Tool28 28
- (Figure 9) 29
- (Figure 10) 30
- EVA controller statistics 31
- ATTO Configuration Tool32 32
- LUN device 33
- LUN path information 34
- ATTO Configuration Tool36 36
- LUN target information 37
- LUN adapter information 38
- LUN statistics 39
- Resetting LUN statistics 40
- ATTO Configuration Tool42 42
- A Multipath configuration 43
- Multipath configuration46 46
- Multipath configuration48 48
- B EVA storage system software 49
- EVA storage system software50 50
- Overview 51
- EVA storage system software52 52
- Troubleshooting tools 53
- ATTOCelerityFCLog utility 54
- System NVRAM options 55
- Enabling debug output 56
- Collecting debug output 56
- ATTO Celerity IORegistry 56
- Troubleshooting examples 57
- Server freezes or hangs 59
- Escalation checklist 61
Produits connexes et manuels pour Lecteurs MP3/MP4 Mpio DMG
(33 pages)
(10 pages)
(45 pages)
(50 pages)Vivitek D8010W manuály
Uživatelské manuály a uživatelské příručky pro Projektory Vivitek D8010W.
Poskytujeme 1 manuály pdf Vivitek D8010W ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels