Mpio HD 200 Guide de l'utilisateur Page 127
- Page / 258
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring an FCIP route
Step 1. Verify your system requirements
Verify that you have the following for both the local site and the remote site (see “MPX200 basic
FCIP configuration” (page 108)):
• HP MPX200 Multifunction Router 1-GbE Base Chassis or HP MPX200 Multifunction Router
10-1 GbE Base Chassis. Note that FCIP is currently supported only on MPX200 1 GbE ports.
• HP MPX200 Half Chassis FCIP License
• Continuous Access EVA
• EVA3000/5000, EVA4x00/6x00/8x00, P63x0/P65x0, XP24000/20000/12000/10000,
or P9500 storage systems
• 3PAR StoreServ 10000/7000, 3PAR T-Class/F-Class
• FC fabrics consisting of B-series C-series, or H-series switches
• Cat 5e network cable, three per site (mgmt, (2) FCIP)
• Optical SFP transceiver and FC cable, two per site
• MPX200 serial console cable adapter, Cat 5e network cable
Additional equipment for the local site and remote site (see “MPX200 high-availability configuration
with one or two long-distance links” (page 112) and “MPX200 configuration with remote IP Distance
gateway (mpx110)” (page 113)) is as follows:
• HP MPX200 Multifunction Router 1-GbE Upgrade Blade (MPX200 blade for redundancy)
◦ HP MPX200 Multifunction Router 10–1 GbE Upgrade Blade. Note that FCIP is currently
supported only on MPX200 1 GbE ports.
Or
◦ HP Storage Works MPX200 Full Chassis FCIP License
NOTE: For the Full Chassis FCIP License, you need to install a license for only one of
the two blade serial numbers in the chassis. When the Full Chassis FCIP License is applied
to the blade it enables both slots. Replacement blades can work in either slot with no
need for another FCIP license.
NOTE: For the latest information about operating system and multipath software support, see
SPOCK at the website http://www.hp.com/storage/spock. You must sign up for an HP Passport
to enable access.
Step 2. Pre-installation checklist
Before you begin the configuration process, contact your system administrator for the following
information for both sites:
• IP address, subnet mask and gateway for the MPX200 management port (if not using DHCP)
• IP address, subnet mask and gateway for the first available GE port
• IP address of the remote MPX200 that connects to the first available GE port
• IP address, subnet mask and gateway for the second available GE port
• IP address of the remote MPX200 that connects to the second available GE port
• FCIP Link Parameters, Guaranteed Bandwidth, Round-Trip-Time, Quality Of Service,
VLAN/Priority
Configuring an FCIP route 127
- Abstract 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- Contents 9 9
- MPX200 features 10
- MPX200 storage system support 10
- Management software 12
- Installation recommendations 20
- Total number of initiators 21
- Use of iSNS 21
- Use of iSCSI ports 21
- Balancing the load 21
- 10-GbE initiators 22
- Prerequisites 22
- General IP-SAN 23
- Network latency 25
- 3 Installing the MPX200 26
- Rack mounting the MPX200 27
- 1. Power cord 29
- Rack mounting the MPX200 29 29
- 4. Bezel3. Bracket arrows 30
- 30 Installing the MPX200 30
- Fibre Channel zoning 31
- Setting up the iSCSI IP ports 34
- Code load 36
- Locating the MPX200 38
- Removing an iSCSI controller 39
- Setting up the iSCSI ports 41
- LUN provisioning 42
- LUN provisioning 43 43
- Alternate procedure 45
- LUN management 48
- LUN management 49 49
- Figure 48 Expanded ports 50
- LUN management 51 51
- Supported IP network adapters 58
- IP network requirements 58
- Figure 56 Host details 63
- Multipathing 65
- Assigning device names 78
- Target bindings 78
- Mounting file systems 79
- Unmounting file systems 79
- MPxIO overview 83
- Editing the sgen.conf file 85
- Creating an sgen driver alias 86
- #mpathadm list lu 88
- Setting up authentication 97
- Setting up authentication 103 103
- Setting up authentication 107 107
- 8 MPX200 FCIP 108
- FCIP and iSCSI performance 110
- 112 MPX200 FCIP 112
- 114 MPX200 FCIP 114
- 116 MPX200 FCIP 116
- 118 MPX200 FCIP 118
- IP performance tuning 121
- Distance 122
- Bandwidth per route 122
- MTU/Jumbo frames 122
- Compression 123
- FCIP link diagnostics 126
- Configuring an FCIP route 127
- Step 3. Rack-mount the MPX200 128
- Step 4. Install the SFPs 128
- Install FCIP license 129
- Configuring an FCIP route 131 131
- 132 MPX200 FCIP 132
- FCoE configurations 133
- Ethernet 134
- Figure 114 Host type 137
- Figure 115 Host properties 137
- MPX200 chassis diagnostics 141
- Fibre Channel Port LEDs 142
- POST diagnostics 142
- Locating the MPX200 blade 144
- MPX200 log data 144
- MPX200 statistics 144
- MPX200 ping command 144
- WANLink diagnostic 145
- Issues and solutions 147
- Intended audience 151
- Related documentation 151
- Contacting HP 151
- Related information 152
- Typographical conventions 152
- Rack stability 153
- Product warranties 153
- 12 Documentation feedback 154
- A Command reference 155
- Fciproute 158
- Example 2: 159
- NoneAuthority 161
- Commands 161 161
- Initiator 163
- Commands 165 165
- Set alias 169
- Set CHAP 169
- Set chassis 170
- Commands 171 171
- Set features 172
- Set iSCSI 172
- Set iSNS 172
- Set Mgmt 173
- Set properties 174
- Set SNMP 174
- Set system 175
- Set VPGroups 175
- Show CHAP 178
- Show chassis 178
- Show fciproutes 179
- Show features 180
- Show initiators 180
- Show initiators LUNmask 180
- Show iSCSI 181
- Show iSNS 181
- Show logs 182
- Show LUNinfo 182
- Show LUNs 183
- Show LUNmask 183
- Show memory 184
- Show mgmt 184
- Show NTP 184
- Show perf 185
- Show presented targets 186
- Show properties 187
- Show SNMP 187
- Show stats 187
- 188 Command reference 188
- Commands 189 189
- Show system 190
- Show targets 190
- Show VPGroups 191
- Shutdown 191
- Traceroute 192
- Wanlinktest 192
- 194 Command reference 194
- Logging on to an MPX200 195
- Modifying a configuration 196
- SNMP parameters 199
- Management Information Base 200
- FC port table 202
- Initiator object table 204
- LUN table 205
- VP group table 207
- Sensor table 209
- Notifications 210
- Notification objects 211
- Agent startup notification 212
- Agent shutdown notification 212
- FC port down notification 212
- Target device discovery 212
- Notifications 213 213
- Notifications 215 215
- D Log messages 216
- Table 35 DM log messages 232
- Table 36 WD log messages 235
- Regulatory compliance notices 240
- BSMI notice 241
- Safety notices 242
- Power cords 243
- Japanese power cord statement 244
- Chinese warning messages 244
- English notice 244
- Dutch notice 244
- Czechoslovakian notice 245
- Estonian notice 245
- Finnish notice 245
- French notice 245
- German notice 245
- Greek notice 246
- Hungarian notice 246
- Italian notice 246
- Latvian notice 247
- Lithuanian notice 247
- Polish notice 247
- Portuguese notice 247
- Slovakian notice 248
- Slovenian notice 248
- Spanish notice 248
- Swedish notice 248
- Username: guest 250
- Password: password 250
- MPX200> admin start 250
- Glossary 251
- 252 Glossary 252
- 254 Glossary 254
- 256 Index 256
- 258 Index 258
Commentaires sur ces manuels
Produits connexes et manuels pour Lecteurs MP3/MP4 Mpio HD 200
(3 pages)
(48 pages)
(45 pages)
(50 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.216 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med
Hello! Crazy discounts, hurry up! We are Drop Dead Studio and our goal is to help companies achieve impressive sales results through automated marketing. I. We sell fresh databases for GSA Search Engine Ranker. • The databases are updated monthly through 24/7 parsing and by connecting purchased databases from other sources. • You have the option to purchase a one-time fresh database or pay for a lifetime subscription for updates. ATTENTION! 40% discount only until 04/10/2024! When ap